Select Page

MR380-1-3 Universal SM/MM E-Stop and Switch Controller

MR380-1 Fiber Optic E-Stop DIN Rail Mount Controller
ZapFree   
MR380-1 Fiber Optic Emergency Stop Controller

MR380-1-3

MR38X Series Universal DIN Rail Mount Controller

MR380 Fiber Optic Signaling Sensors are used anywhere where conventional electromechanical controls cannot be used – both harsh and hazardous environments. The MR380-1-3 Universal Controller Module is the active optical and electrical interface for all MR380 series ZapFREE® Emergency Stop, Microswitch, and other Signaling Sensor products. This controller is compatible with both multimode (50/125 and 62.5/125) and single mode (9/125) based sensors in the MR380 series.

Features

  • DIN rail mountable module
  • Ex rated Inherently Safe Optical Radiation
  • Controller is installed outside the hazardous area
  • Interference-free transmission up to 10km (6 miles) with single mode fiber
  • Universal controller supports both multimode (50/125 and 62.5/125) and single mode (9/125) fiber links
  • Depending on sensor type, multiple sensors can be optically wired in series

 Interfaces 

  • DPDT relay contacts
  • Digital status outputs, 5V and 24V
  • Depending on sensor type, digital outputs and relay implement know default failure state

Connect Multiple E-Stops in Series

Multiple FO E-Stops

Extend Dry Contacts to Multiple Areas

How To Use Multiple Controllers to Extend FO E-Stop Contacts To Multiple Areas

Extend Reach of Existing EM E-Stops:

Specifications

 

Functional States Applies to MR380 E-STOP Sensor Only
Normal RESET (Up Position) Digital 5V and 24V Outputs=HI

NC contacts=Closed, NO contacts=Open

ACTIVATED (Down Position)

Broken Fiber, Loss of Optical Signal, or Controller Failure

Digital 5V and 24V Outputs=LOW

NC contacts=Open, NO contacts=Closed

Digital Outputs  
5V Logic 5 VDC/2k Ω Load Max
24V Logic 24 VDC/2k Ω Load Max
Relay Contacts 2x Form C (CO)
Switching Power Rating 60 W / 62.5 VA
Contact Material AgNi, Gold Covered
DC Rating 75 V @ 0.75A; 24 V @ 2A
AC Rating 50 V @ 1A; 24 V @ 2A
Optical Class I Eye Safe, 1310nm
Fiber Compatibility Use with Multimode OM1 62.5/125, Multimode OM2/OM3 50/125, or Single Mode OS1/OS2 9/125m fiber
System Loss Budget 23dB (minimum), 25dB (typical)
Maximum Distance Distance is a function of user’s system loss budget which is the total round-trip loss of all optical link components – sensor(s), connectors, splices and cable segments. Direct run E-Stop Links can operate up to 20km.
Consult Application Note AN118 for more information.
Interface NOTE: Electrical connections shall not exceed 3 meters.
Electrical 10-pin Screw Terminal, 30-14 AWG (Phoenix Mating Plug 1803659)
Optical LC-Duplex, 50/125 OM-2 or 62.5/125μm OM-1 Multimode Fiber
Power Supply +24 VDC, <80 mA input
Functional Safety Consult Declaration of Conformity for additional F.S. information
Classification MR380 System is classified Category 2 per ISO13849-1
MTTFd 4.14 E+06 hours (70.8 years)
Performance Level (PL) PL=c
Safety Integrity Level (SIL) SIL=1
Explosive Atmospheres  
EX Classification Controller shall be installed in non-hazardous location only
Power supply to Controller shall be current limited to 200mA or less
IECEx Test Report (ExTR) GB/CML/ExTR 16.0105/00 (Multimode Controllers)
ATEX [EPL Mb/Gb/Gc/Db/Dc]
EAEU/GOST [EPL Mb/Gb/Gc/Db/Dc]
IEC Ex [EPL Mb/Gb/Gc/Db/Dc]
North America Controller shall be installed in non-hazardous location only
Environmental Performance  
Temperature/Humidity -5°C to +55°C (23°F to +131°F), 0-95% RH, Non-Condensing
Ingress Protection IP50
Physical Attributes  
Mounting 35mm DIN Rail
Housing 11.4 x 8.9 x 3.2 cm (4.5 x 3.5 x 1.25 inches)
Weight 230 g (8.1 oz)

Specifications subject to change without notice

TO ORDER

Call +1-805-389-6600 or email sales@micronor.com

Ordering Information

MR380-1-3 Universal Multimode/Single Mode E-Stop and Switch Controller
For use with Multimode OM1 62.5/125 and OM2 50/125,
and Single Mode OS1 9/125 Fiber Links

Quick Ship Configurations

MR380-1-3 Universal MM/SM E-Stop and Switch Controller
MR387-2S-1R5 E-Stop, 30mm Button, For use with OM1 62.5/125 or OM2/OM3 MMF Link, Duplex-LC Pigtail Length=1.5m
MR387-2S-D00 E-Stop in IP Housing, 30mm Button, For 62.5/125 MMF Link, Interface=ODVA IP-LC Receptacle
MR387-3S-1R5 E-Stop, 30mm Button, For use with OS1/OS2 9/125 SMF Link, Duplex-LC Pigtail Length=1.5m
MR387-3S-D00 E-Stop in IP Housing, 30mm Button, For use with OS1/OS2 9/125 SMF Link, Interface=ODVA IP-LC Receptacle
 
0 Item | $0.00
View Cart